APC Smart-UPS RT 2200VA RM 120V. UNITED STATES - Select your location; Partner Login. Smart UPS signalling RS-232 cable, USB cable, User Manual. Smart-UPS On-Line Features & Benefits. Serial connectivity. Provides management of the UPS via a serial port. Network manageable. Provides remote power management of the UPS over the.
- Smart-UPS XL 2200VA - read user manual online or download in PDF format. APC Smart-UPS XL 2200VA SUA2200RMXL3U User Manual. Page of 22 Go. Smart-UPS XL 3U Rack.
- APC Smart-UPS. Uninterruptible Power Supply. 230 VAC User’s Manual. 990-7020C, Revision 7, 3/00. Initial Start-Up. To obtain warranty coverage, please fill out and return the warranty registration card now. Inspection Inspect the UPS upon receipt. Notify the carrier and dealer if there is damage. The packaging is recyclable; save it for reuse or dispose of it properly.
Advertising
Smart-UPS XL 3U Rack Mount 2200/3000 VA 120/230 Vac; 3000 VA 100/200 Vac User Manual
Troubleshooting
The Overload LED is illuminated and the UPS emits a sustained alarm tone
The UPS is overloaded.
The connected equipment exceeds the specified “maximum load” as defined
in Specifications on the APC Web site, www.apc.com.
The alarm remains on until the overload is removed. Disconnect nonessential
equipment from the UPS to eliminate the overload condition.
The UPS continues to supply power as long as it is online and the circuit
breaker does not trip; the UPS will not provide power from batteries in the
event of a utility voltage interruption.
The alarm remains on until the overload is removed. Disconnect nonessential
equipment from the UPS to eliminate the overload condition.
The UPS continues to supply power as long as it is online and the circuit
breaker does not trip; the UPS will not provide power from batteries in the
event of a utility voltage interruption.
The Disconnected Battery/ Replace Battery LED is illuminated
The Disconnected Battery/Replace
BatteryLED flashes and a short beep is
emitted every two seconds to indicate
the battery is disconnected.
emitted every two seconds to indicate
the battery is disconnected.
Check that the battery connectors are fully engaged.
Weak battery.
Allow the battery to recharge for 24 hours and perform a self-test. If the
problem persists after recharging, replace the battery.
problem persists after recharging, replace the battery.
Failure of a battery self-test:
Disconnected Battery/
Replace Battery LED illuminates and
the UPS emits short beeps for one
Replace Battery LED illuminates and
the UPS emits short beeps for one
minute. The UPS repeats the alarm
every five hours.
every five hours.
Allow the battery to recharge for 24 hours. Perform the self-test procedure to
confirm the replace battery condition. The alarm stops and the LED clears if
the battery passes the self-test.
If the battery fails again, it must be replaced. The connected equipment is
the battery passes the self-test.
If the battery fails again, it must be replaced. The connected equipment is
unaffected.
The Site Wiring Fault LED on the rear panel is illuminated (120 V models only)
The UPS is plugged into an improperly
wired utility power outlet.
wired utility power outlet.
Wiring faults detected include missing ground, hot-neutral polarity reversal,
and overloaded neutral circuit.
Contact a qualified electrician to correct the building wiring.
and overloaded neutral circuit.
Contact a qualified electrician to correct the building wiring.
The input circuit breaker trips
The connected equipment exceeds the
specified “maximum load” as defined
in Specifications on the APC Web site,
specified “maximum load” as defined
in Specifications on the APC Web site,
www.apc.com.
Unplug all nonessential equipment from the UPS.
Reset the circuit breaker.
Reset the circuit breaker.
The AVR Boost or AVR Trim LEDs are illuminated
The system is experiencing very high or
low utility voltage.
Have qualified service personnel check your facility for electrical problems.
If the problem persists, contact the utility company for further assistance.
Problem and/or Possible Cause
Solution
Advertising
This manual is related to the following products:
Popular Brands
Popular manuals
Advertising
14
Smart-UPS XL 3U Rack Mount 2200/3000 VA 120/230 Vac; 3000 VA 100/200 Vac User Manual
Configuration
3. Press 1 and ENTER to select Device Manager.
Select the model by entering the corresponding number, then press ENTER.
4. Press 3 and ENTER to select Configuration.
5. Press 1 and ENTER to select Battery.
6. Press 2 and ENTER to change Battery Settings.
7. Type in the number of external battery packs then press ENTER.
5. Press 1 and ENTER to select Battery.
6. Press 2 and ENTER to change Battery Settings.
7. Type in the number of external battery packs then press ENTER.
Number of external battery packs:
1=1 external battery pack; 2=2 external battery packs; 3=3 external battery packs etc.
8. Press 3 and ENTER to accept the changes.
9. Press ESC multiple times (5) to return to the main menu.
10.Press 4 and ENTER to log out.
9. Press ESC multiple times (5) to return to the main menu.
10.Press 4 and ENTER to log out.
Configure UPS connection settings using UPS terminal mode
Connect the serial cable to the serial port on the back of the UPS. If using USB communication to the UPS,
disconnect the USB cable prior to connecting the serial cable.
1. Open a terminal program, such as HyperTerminal
From the Desktop, go to: Start, Programs, Accessories, Communication, HyperTerminal
2. Follow the prompts to choose a name and select an icon. Disregard the message, '..must install a
modem,' if it is displayed. Click Cancel
Apc Smart Ups 2200
3. Go to File, Properties. Select the COM port that is connected to your UPS. The port settings are:
–
bits per second - 2400
Apc Smart Ups 2200 User Guide
–
data - bits 8
–
parity - none
–
stop bit - 1
–
flow control - none
4. Click OK in each of two windows
5. Press ENTER
5. Press ENTER
Configure the number of external battery packs using UPS terminal mode
1. Once the blank terminal window is open, follow these steps to enter the number of external battery packs:
NOTE: Letter key commands are case sensitive. Use capital letters when using letter key commands.
2. Press Y. The UPS will respond with SM in the command box. If the UPS does not respond to the Y
command, ensure the serial cable is securely connected to the serial port on the UPS. Use only an APC
supplied serial cable.
3. When SM appears in the command box press the > key. The UPS will respond with the number of
external battery packs connected to the UPS. If the UPS has not been previously programmed to
recognize the number of external battery packs this number will be zero.
Apc Smart Ups 2200 Manual
4. Use the + or - keys to change the number of external battery packs. OK will appear in the command box.
5. Press > key. The number of external battery packs will appear in the command box.
5. Press > key. The number of external battery packs will appear in the command box.
NOTE: The + or - keys and the > key must be used again to change the number of external battery packs
Apc 2200 Smart Ups Specs
from this point in the programming.
6. Press R. The UPS will respond with BYE in the command box.
Advertising
This manual is related to the following products:
Popular Brands
Popular manuals